Quick answer
To light a Coleman lantern, first confirm whether you have a liquid-fuel or propane model. For fuel lanterns, pump the tank, open the valve a quarter turn, and hold a flame at the mantle. For propane, attach the canister, turn the gas on low, and light immediately. Always operate in a well-ventilated area.
On this page
A Coleman lantern is a classic piece of camping gear, but the lighting procedure can be confusing if you have not used one in a while, or if you inherited a model without a manual. The exact steps depend on whether you are working with a traditional white-gas lantern or a modern propane version.
This guide walks you through lighting both types safely. You will learn how to prepare the lantern, position the flame correctly, and troubleshoot common issues like flickering or a lantern that will not stay lit. By the end, you will be able to fire up your campsite light with confidence.
Identify your lantern type first
Coleman makes two main lantern families, and the lighting sequence is different for each. A liquid-fuel lantern has a large red or silver fuel tank at the base with a pump plunger on one side. It burns Coleman Fuel or unleaded gasoline. A propane lantern has a smaller base that accepts a disposable green propane cylinder or a hose to a bulk tank, and it has no pump.
Check the label or the base of your lantern before you begin. Using the wrong procedure can flood a fuel lantern or create a dangerous gas buildup in a propane model. If your lantern has been sitting for a season, inspect the mantles for holes and replace any that are torn before you light it.
Lighting a liquid-fuel Coleman lantern
Start in a clear, outdoor area away from tents and dry brush. First, unscrew the fuel cap and fill the tank with clean Coleman Fuel, leaving a small air gap at the top. Tighten the cap securely. Close the lighting valve (the small knob on the side of the generator) by turning it clockwise, then pump the plunger repeatedly until you feel firm resistance in the tank.
Open the lighting valve a quarter turn counterclockwise. You should hear a faint hiss of fuel entering the generator. Immediately hold a long lighter or match directly under the mantle. The mantle will glow and may flare briefly. Once the mantle burns steadily, open the valve fully. If the flame sputters, give the tank a few more pumps.
Lighting a propane Coleman lantern
Propane lanterns are simpler. Attach a fresh propane cylinder by threading it into the lantern base until snug. Do not overtighten. Make sure the lantern’s control knob is in the off position before connecting fuel.
Turn the control knob to the low or light position, then immediately hold a flame at the base of the mantle. The gas ignites with a soft pop and the mantle glows. Once lit, you can turn the knob to high for full brightness. If it does not light on the first try, turn the gas off, wait a few seconds for unburned propane to clear, and try again. Never let gas flow without a flame present.
Mantle care and first burn-in
New mantles need a burn-in before they can produce light. Tie the fresh mantle onto the burner tube, then hold a flame to the entire fabric until it catches fire and burns down to a fragile ash skeleton. Let it cool completely. The ash mantle is what glows when the lantern runs.
After burn-in, light the lantern normally. The mantle will shrink and harden into shape. Avoid bumping the lantern once the mantle is formed; even a light tap can shatter it. Carry spare mantles in your camp kit. A torn mantle creates an uneven flame and can overheat the glass globe.
Troubleshooting common lighting problems
If a fuel lantern will not light, the generator tip may be clogged. Close the valve, let the lantern cool, and use the built-in cleaning needle (on most models) by rotating the cleaning lever several times. Then try lighting again. A weak flame often means low tank pressure: add more pump strokes.
For propane lanterns, a hiss with no ignition usually means the gas is flowing but the spark or match is not reaching the burner. Check that the mantle is intact and the burner tube is not blocked by debris. In cold weather, propane pressure drops; warm the cylinder in your hands or jacket pocket before attaching it. If the lantern pulses or flickers, the fuel may be low or the generator needs cleaning.
Safety tips every time you light a lantern
Always light a Coleman lantern outdoors, never inside a tent, vehicle, or enclosed shelter. Both fuel and propane lanterns produce carbon monoxide and consume oxygen. Keep the lantern on a stable, non-flammable surface and away from anything that can melt or catch fire.
Never refill a hot fuel lantern. Let it cool completely before opening the tank. When you are done for the night, shut off the valve and let the lantern cool before storing it. For propane models, disconnect the cylinder when the lantern is not in use. These habits prevent leaks, burns, and accidental fires at your campsite.
Frequently asked questions
Why does my Coleman lantern flicker after lighting?
Flickering usually means the generator is partially clogged or the fuel pressure is low. On a liquid-fuel lantern, try rotating the cleaning lever and adding more pump strokes. On a propane model, check that the cylinder is not nearly empty and that the control knob is fully open. A torn mantle can also cause an uneven burn.
Can I light a Coleman lantern inside a tent?
No. Coleman lanterns burn fuel and produce carbon monoxide. They also get extremely hot. Always light and run them outside in a well-ventilated area, at least several feet from your tent, to avoid fire and fume risks.
How many pumps does a Coleman fuel lantern need?
Start with several full strokes after filling the tank. If the flame weakens during use, add a few more pumps to restore brightness. Avoid over-pumping to the point where the plunger becomes very hard to push, which can stress the seals.
What do I do if my lantern mantle breaks while lighting?
Turn off the lantern immediately and let it cool. Remove the broken mantle fragments from the burner tube, tie on a new mantle, and perform a fresh burn-in before lighting the lantern again. Never run a lantern with a damaged mantle.
Bottom line
Lighting a Coleman lantern is straightforward once you match the steps to your model. Fuel lanterns need pumping and a careful quarter-turn start, while propane versions light with the turn of a knob. Keep spare mantles on hand, always work outside, and you will have a dependable light source for every camping trip. For more campsite know-how, see our guides on staying comfortable in any weather.